Telemetrie Adapter

Not required for ECU V12

Telemetrie Adapter

Not required for ECU V12

Part no: 61108-0070

Price: 94,01 € (incl. VAT.)

Net price: 79,00 €

Part no:
61108-0070

Price
94,01 €
(incl. VAT.)

Net price:
79,00 €

-
+
Add to Basket

Telemetry Adapter

The JetCat telemetry adapter connects directly to the ECU data bus.
The output of the telemetry adapter is typically directly connected to the receiver
(Telemetry input of the receiver).
The adapter has two outputs connected in parallel so that another device or sensor can be connected to the 2nd port.

The following values can be transferred depending on the system used:

  • Exhaust gas temperature in ° C
  • Turbines actual speed in 1/min
  • Pump voltage in V
  • Voltage of the turbine battery in V
  • Current consumption in A. Only for ECU V10.0 or higher
  • Battery capacity in mAh (Turbine battery). Only for turbines with generator function (for example P220RXi, P180-NX)
  • Turbine state and error codes
  • rest fuel in ml / rest fuel in%
  • fuel flow in ml/min
  • Altitude in meters. Only with ECU V10.0 or higher
  • Thrust in N
  • Turbines Set speed in 1/min
  • Airspeed in km/h
  • Speed of second shaft (propeller speed for turboprops or main rotor speed for helicopter engines)

 

Starting Telemetrie Adapter with firmware V. 9.0, the following systems are supported:

      V10.0         V6.0    
Ab ECU Software Version            10.4P 6.42
Futaba SBUS-2
Graupner HOTT
MPX M-Link1
MPX M-Link2
Jeti
Jeti-NoAlarms  
Mikado Vbar  
PowerBox Core    
Spektrum    

 

ATTENTION:

  • ECU V5/6: LED I/O board 61108-0000 with 8-pin ERNI socket necessary
  • ECU V10 LED I/O board Mini 61108-0050 necessary
  • ECU V6 with firmware 6.42 or higher required 
Telem-Adapter-German-V1.1 -Anleitung Vers. 4.pdf
 
jeti-telemetrie-wav-files.zip
 
Info Telemetrie Adapter.pdf
 
Please upload as .zip file. (Maximum upload size: 10MB)
* mandatory fields

Telemetry Adapter

The JetCat telemetry adapter connects directly to the ECU data bus.
The output of the telemetry adapter is typically directly connected to the receiver
(Telemetry input of the receiver).
The adapter has two outputs connected in parallel so that another device or sensor can be connected to the 2nd port.

The following values can be transferred depending on the system used:

  • Exhaust gas temperature in ° C
  • Turbines actual speed in 1/min
  • Pump voltage in V
  • Voltage of the turbine battery in V
  • Current consumption in A. Only for ECU V10.0 or higher
  • Battery capacity in mAh (Turbine battery). Only for turbines with generator function (for example P220RXi, P180-NX)
  • Turbine state and error codes
  • rest fuel in ml / rest fuel in%
  • fuel flow in ml/min
  • Altitude in meters. Only with ECU V10.0 or higher
  • Thrust in N
  • Turbines Set speed in 1/min
  • Airspeed in km/h
  • Speed of second shaft (propeller speed for turboprops or main rotor speed for helicopter engines)

 

Starting Telemetrie Adapter with firmware V. 9.0, the following systems are supported:

      V10.0         V6.0    
Ab ECU Software Version            10.4P 6.42
Futaba SBUS-2
Graupner HOTT
MPX M-Link1
MPX M-Link2
Jeti
Jeti-NoAlarms  
Mikado Vbar  
PowerBox Core    
Spektrum    

 

ATTENTION:

  • ECU V5/6: LED I/O board 61108-0000 with 8-pin ERNI socket necessary
  • ECU V10 LED I/O board Mini 61108-0050 necessary
  • ECU V6 with firmware 6.42 or higher required 
Telem-Adapter-German-V1.1 -Anleitung Vers. 4.pdf
 
jeti-telemetrie-wav-files.zip
 
Info Telemetrie Adapter.pdf
 
Please upload as .zip file. (Maximum upload size: 10MB)
* mandatory fields