LCU-PRO-USB
New LCU-PRO V2 - Art.: 61162-0031
LCU-PRO-USB
New LCU-PRO V2 - Art.: 61162-0031
61162-0030
Automated lighting control for your model The JetCat-LCU can automatically control your model lighting depending on the engines operation condition.
Via the additional 3x RC inputs individual lights can also be directly RC controlled (e.g. for landing lights)
Examples of automatic lighting controlvia engines state:
| Engine state | Jet-model | Helicopter model |
| Engine OFF, no cooling | All lights OFF | |
| Engine start | Flash lights= ON Position lights= OFF |
|
| Engine Ignition detected | Position lights for 4 secs ON then OFF again | Position lights and ACL (=anti-collision light) for 4 secs ON then OFF again |
| Engine started up and idle rpm reached | Flash lights= ON Position lights= ON |
|
| Engine at max/full rpm | Afterburner lights ON when engine RPM >90% and full RPM commanded | Max Rpm reached and stable ACL =ON |
| Engine OFF, cooling | Flash lights=ON, all other lights=OFF | Flash lights=ON, all other lights=OFF |
| Battery low | All lights OFF | All lights OFF |
| FailSafe condition detected | Position lights and afterburner lights flash rapidly | Position lights and ACL flash rapidly |
| Fuel low | Position lamps flashing in 4-second interval | Position lamps flashing in 4-second interval |
- Easy programming with only 2 buttons
-
LCU automatically switches ON/OFF with RC power, no additional switch necessary
- Fully opto-isolated RC inputs
-
USB port for parameter setting /programming via PC / laptop
-
Can be powered from engine battery.
-
3x independent RC inputs /outputs (V-cable function on board)
-
Input for control and power supply of the LCU via JetCat-ECU (8-pin flat cable)
-
14x outputs: 11x multifunction, 2x afterburner, 1x switching output
-
22x 1W - emitters connectable (each multifunction output can drive up to 2 LEDs)
-
2x afterburner rings directly connectable (output regulated to 6.6V)
-
Afterburner lights are automatically triggered from ECU at full throttle and engine running.
-
Each output has a dedicated control LED
- Status LED (green/ yellow/ red) for programming aid and voltage monitor
-
Battery connection via MPX plug (or from ECU)
-
Each output function (LED) can be freely assigned to an RC input or be automatically controlled from ECU.
-
Extensive adjustments and combinations possible Anodised aluminum upper shell
| Name | Value |
|---|---|
| Pressure ratio | - |
| Mass flow (kg/s) | - |
| Consumption Full load (ml/min) | - |
| Consumption idle (ml/min) | - |
| Weight [g] | 50 |
| Dimensions of the diameter (mm) | H=15mm ; L=73mm; B=51mm |
| Length (mm) | - |
| Battery recommendation | - |
| Carton dimensions (LxWxH; cm) | - |
| Exhaust gas temperature (°C) | - |
LCU-Pro-USB_05042017_V4.pdf
Automated lighting control for your model The JetCat-LCU can automatically control your model lighting depending on the engines operation condition.
Via the additional 3x RC inputs individual lights can also be directly RC controlled (e.g. for landing lights)
Examples of automatic lighting controlvia engines state:
| Engine state | Jet-model | Helicopter model |
| Engine OFF, no cooling | All lights OFF | |
| Engine start | Flash lights= ON Position lights= OFF |
|
| Engine Ignition detected | Position lights for 4 secs ON then OFF again | Position lights and ACL (=anti-collision light) for 4 secs ON then OFF again |
| Engine started up and idle rpm reached | Flash lights= ON Position lights= ON |
|
| Engine at max/full rpm | Afterburner lights ON when engine RPM >90% and full RPM commanded | Max Rpm reached and stable ACL =ON |
| Engine OFF, cooling | Flash lights=ON, all other lights=OFF | Flash lights=ON, all other lights=OFF |
| Battery low | All lights OFF | All lights OFF |
| FailSafe condition detected | Position lights and afterburner lights flash rapidly | Position lights and ACL flash rapidly |
| Fuel low | Position lamps flashing in 4-second interval | Position lamps flashing in 4-second interval |
- Easy programming with only 2 buttons
-
LCU automatically switches ON/OFF with RC power, no additional switch necessary
- Fully opto-isolated RC inputs
-
USB port for parameter setting /programming via PC / laptop
-
Can be powered from engine battery.
-
3x independent RC inputs /outputs (V-cable function on board)
-
Input for control and power supply of the LCU via JetCat-ECU (8-pin flat cable)
-
14x outputs: 11x multifunction, 2x afterburner, 1x switching output
-
22x 1W - emitters connectable (each multifunction output can drive up to 2 LEDs)
-
2x afterburner rings directly connectable (output regulated to 6.6V)
-
Afterburner lights are automatically triggered from ECU at full throttle and engine running.
-
Each output has a dedicated control LED
- Status LED (green/ yellow/ red) for programming aid and voltage monitor
-
Battery connection via MPX plug (or from ECU)
-
Each output function (LED) can be freely assigned to an RC input or be automatically controlled from ECU.
-
Extensive adjustments and combinations possible Anodised aluminum upper shell
| Name | Value |
|---|---|
| Pressure ratio | - |
| Mass flow (kg/s) | - |
| Consumption Full load (ml/min) | - |
| Consumption idle (ml/min) | - |
| Weight [g] | 50 |
| Dimensions of the diameter (mm) | H=15mm ; L=73mm; B=51mm |
| Length (mm) | - |
| Battery recommendation | - |
| Carton dimensions (LxWxH; cm) | - |
| Exhaust gas temperature (°C) | - |
